Category: Electromagnetic mill

Sand grinding in vortex layer devices

Sand grinding is a necessary stage in preparing the material for its further use in construction and industry. It is one of the basic ingredients for exterior surface finishing, plasters, mortars, and floorings. It is used in production of paving flagstones, dry mortars, glass, paints and varnishes, etc. At the same time, the quality ofRead More

fuel preparation

Marine fuel preparation

For the purposes of practical applications of ferromagnetic particles vortex layer devices, we would like to speak about the area such as fuel preparation on ships. Types of marine fuel If we compare a ship with a motor vehicle by special aspects of fuel consumption, two important differences can be highlighted. The first difference isRead More

rongalite production

Rongalite production in a vortex layer device

In the previous articles, we spoke about the capabilities of a vortex layer device in terms of grinding, mixing, and activating various substances. But the device can also be used to run and accelerate chemical reactions. One of such reactions is the reduction of sodium bisulfite in rongalite production. What is rongalite and where isRead More

oil shale grinding

Oil shale grinding in obtaining light petroleum products

In this article, we will discuss oil shale grinding, the process that takes place in obtaining light petroleum products from heavy oil residues. What are oil shales and how are they applied in obtaining light petroleum products? The process of obtaining fuel fractions from oil is accompanied by formation of heavy oil residues. These includeRead More

lubricant grease production

Lubricant grease production by means of a vortex layer device

Lubricant grease is a thick anti-friction, water-repellent multipurpose lubricant. It is a slippery, fatty, pasty mass of yellow or brown color. It is produced on the basis of industrial (petroleum, mineral) oils. Lubricant grease production involves thickening the raw stuff by adding the calcium soap derived from fatty acids through saponification. The main advantage ofRead More

cocoa shell grinding

Cocoa shell grinding as a waste recycling method

In this article, we will tell you how cocoa shell is ground. Cocoa shell is the husk of cocoa beans formed in the process of crude chocolate production. World market of cocoa beans The main suppliers of cocoa beans to the world market are African countries. If we take the average annual consumption of thisRead More

fodder production

Fodder production by means of a vortex layer device

In this article, we will discuss fodder production using electromagnetic technologies. Liquid mixed fodder is a feed compound with the moisture content of 70–80% in the form of a homogeneous suspension of ground grain raw stuff, water, and additives. It is applied for feeding the calves using a milk substitute emulsion. Feed compounds in theRead More

fast-neutron reactor

Special aspects of fuel production for fast-neutron reactors

According to various estimates, the share of nuclear energy is at least 10–16% of all the energy resources generated in the world. In some countries, such as France, nuclear energy ranks high — 71.6%. In China, the share of nuclear energy does not exceed 4%. The use of nuclear energy is a matter of debate,Read More

sugar beet processing

Sugar beet processing — what shall be done to waste?

Sugar beet processing is an important technological procedure in sugar production. This product is extensively used all over the world as evidenced by large production volumes — at least 168 million tons per year. Brazil, India, the European Union, Thailand, China, the United States, and Russia stand out of major sugar producers. Countries of warmRead More

production of cutting fluids

Production of cutting fluids by means of a vortex layer device

Cutting fluids are emulsions used in the field of mechanical processing of metals, stone, ceramics, and plastics. Such means are used to lubricate and cool the workpiece and the working tool in the zone of their contact while drilling, cutting, and pressing are performed. Basically, cutting fluids are used for turning and milling the workpieces.Read More

burovoy-rastvor-2

Drilling mud production in a vortex layer device

In this article, we will discuss drilling mud production by means of a ferromagnetic particles vortex layer technology and evaluate the prospects of applying this technology in the oil and gas industry. Drilling mud is an important part of the technology for development of mineral resources (oil and gas). It is responsible for several functionsRead More

Peat gel

Peat gel production in vortex layer device

Peat gel is a biologically active fertilizer based on humic acids, trace elements, minerals, and nitrogen compounds. It is made from peat. It is a humic preparation that acts as a plant growth catalyst and a soil remediator. It also acts as an immunomodulatory agent for poultry and animals that contributes to boosting their immunityRead More

coffee milling

Coffee milling in vortex layer devices

Coffee milling is a mandatory stage of manufacturing both a natural product from roasted coffee beans and an instant freeze-dried, granulated, or powdered beverage. Depending on the type of coffee, grinding is performed to a certain fraction. It may be coarse grinding with a size of almost a millimeter, medium, fine grinding to tenths ofRead More

cement grinding

Cement grinding in vortex layer devices

In this article, we will discuss how cement grinding, cement activation, microcement production, and dry mortar production are carried out by means of vortex layer devices. Cement is the most expensive part of concrete that considerably determines the quality of concrete products, as well as the reliability and durability of structures built on their basis.Read More

peper milling

Electromagnetic pepper milling

Pepper milling is a technological process for grinding a product to obtain a powdery constituent used as a base, an additional or active ingredient in the production of food supplements, spices, mixtures, ointments, and aerosols. In order to grind pepper on an industrial scale, special mills are used. Some of them operate according to theRead More

coal grinding

Coal grinding to obtain water-coal fuel

Coal grinding is one of the stages of the technological process for obtaining water-coal fuel. Water-coal fuel owes its emergence to water-coal slurry which was used in the 50–60s of the past century in order to find application for watered coal particles. At that time, the technology of water-coal slurry was considered to be ratherRead More

electromagnetic seed processing

Pre-sowing electromagnetic seed processing

Pre-sowing seed processing means preparation of sowing material for germination and planting. It is carried out with the purpose of improving the germination and further growth, as well as increasing the crop yields. It also impacts on the resistance of plants against the influence of external factors, boosting their immunity and protection from diseases andRead More

lubricants production

Lubricants production in the vortex layer device

In this article, we will discuss lubricants production using vortex layer devices — the equipment designed to intensify various technological processes. Lubricants are essential to ensure the equipment operability and performance. The main purpose of lubricants is to reduce friction and wear in rubbing parts of mechanisms which allows increasing the mechanical efficiency of theRead More

Wastewater Treatment Complex

Hospital Water Treatment Plant

Wastewater from hospitals can contain traces of anything from viruses and multi-resistant bacteria to medical contrast agents and chemicals for cancer treatment. Small amounts of hormone-disrupting substances and other medicine residues are also part of the mix that passes from patients through hospital toilets and into public sewer systems. According to the World health OrganizationRead More

blank

Efficient Desulfurization of Crude Oil With the Vortex Layer Device

The complexity of treatment and desulfurization of oil and it products to remove undesired sulfur compounds is due to the complex composition of the material and a vast variety of sulfuric compounds. Crude oil consists of carbon, hydrogen, sulfur, oxygen and nitrogen. There are small portions of metals, mostly nickel and vanadium. Hydrocarbons are 75%Read More

blank

Vortex Layer Devices in Gold Production

Gold is used in several fields: as part of national reserves; in medicine (dentistry, pharmaceuticals and cosmetology). In this case gold is used in implants, medicines and cosmetics. The amount of gold used in this field is relatively small and remains below 2% of the total demand; electronics (information technologies and telecommunications). In this fieldRead More

blank

Cement Grinding in Ball Mills and Vortex Layer Devices

Cement and concrete are the second most used substances in the world, after water. On average, the per capita consumption of cement is one ton. This material is widely used as a binder in the production of concrete, reinforced concrete and various construction mixes. The demand for cement in construction of new buildings, repairs andRead More

blank

Coal-Water Fuel Production

Natural energy reserves are unevenly distributed, making shortages of energy resources common in many countries. This is an incentive for three things: looking for less expensive imports, saving energy and developing alternative heat and energy sources. According to industry professionals, coal-water fuel (also known as CWF or coal slurry) is a promising product. CWF isRead More

Fuel Purification

Improving Water Fuel Emulsion Quality

Practical experience of marine power plant operation shows that their reliability, mean time between failures and time before overhaul depends on operation parameters related to fuel quality. Many river vessels use diesel fuel and fuel oil for propulsion. Fuel always contains sulfur and its sulfuric compounds (mercaptans, sulfides, disulfides etc). These substances reduce quality andRead More

wastewater

Removal of Heavy Metals from Wastewater

Removal of heavy metals and neutralization of heavy metals are words instantly familiar to all environmental scientists and wastewater purification specialists. In this article we will discuss the existing methods of removal of heavy metals, analyze benefits and limitations and will suggest techniques to improve efficiency of wastewater purification. What are the heavy metals HeavyRead More

Press

GlobeCore In The Media: the Cement Americas Magazine

The new issue of the Cement Americas Magazine came out in September 2018. The magazine published an article by Frank May, GlobeCore service engineer, titles The Promising Application of Vortex Layer Devices with Ferromagnetic Elements for Cement Improvement. The article discusses one of the main reasons for cement deterioration which increases cement consumption and includesRead More

wastewater disinfection

Disinfection of wastewater

Disinfection is a complex process of destroying parasites that spread invasive diseases (caused by helminth parasites and arthropods). Sanitary regulations and rules set requirements for deworming/ disinfection. The word “disinfection” came from Latin words “invasio” (invasion) and “des” (from). The quality wastewater treatment is a pressing issue in most countries. The reason is a growingRead More

blank

Urban wastewater treatment

Domestic wastewater of cities and countries is now overwhelming. The sewage treatment facilities have used to the limit all available reserves. The existing technological lines that proved themselves over the years [120, 134] do not cope with the  increased flow of wastewaters. The new sewage treatment facilities are expensive to build. It would seem aRead More

blank

Purification of waste water from phenol and other organic contaminants

In most facilities, such water is purified by oxidizing phenol and other organic contaminants by manganese peroxide, sodium or potassium dichromate at 95-100º С. The oxidation process takes 3 to 5 hours, consuming 5 grams of oxidant per 1 gram of phenol. The purification unit with 12 reactors 25 m3 each can purify 400 to 600 m3 ofRead More

blank

Removal of hexavalent chrome and other heavy metals

The nature of the vortex layer used for treatment of waste water containing hexavalent chrome and other heavy metals allows to radically reduce reagent consumption, achieves a more complete purification and makes the process continuous. Ferromagnetic elements in the active zone of the AVS device, in the electromagnetic field, intensively mix the reagents entering theRead More

blank

Removal of arsenic from waste water

A pressing problem of mining and ore industry is the removal of arsenic from waste water by precipitating it using iron hydroxide or reduction by Na2S, K2S, FeS2. The sedimentation process occurs when a ferrous salt, such as FeCl3, forms a soft amorphous sediment Fe(OH)3 in alkaline environment, which has larger active area. As theRead More

blank

Removal of cyanides

The most toxic waste waters are those containing both simple cyanides (with CN—ions) and complex [Cu(CN2)—], [Cu(CN3)-2], [Zn(CN4)-2] etc. Total concentration of simple and complex cyanides varies from 10-15 to 150-300 mg/liter. The most widespread method today is reagent method of oxidation by calcium hypochlorite Ca(OCl)2, hypochlorite lime CaOCl2 or gaseous chlorine. Most of the cyanide-containing waterRead More

blank

Removal of fluor and nitric compounds from waste water

Research performed in the area of decontamination and fluor removal from waste water using AVS shows (table 5) that these devices are more efficient compared to the existing equipment. Fluor removal and transformation of phosphates into water-insoluble compounds occurs in one stage. The content of fluor in purified waste water in optimal conditions (pH =Read More

Waste+Water+Treatment

Neutralization of wastewater containing petroleum products

Wastewater containing petroleum products are among the most difficult to neutralize.. Especially difficult for processing are wastewaters containing, in addition to petroleum products, metal shavings, sand, rags and other inclusions, both solid and liquid. Therefore, wastewater is very difficult to classify. In some cases, they are divided into types: “flammable” or “non flammable”. For example,Read More

wastewater

Water purification

The conditions created in the processing area of the AVS allow to carry out practically any technological processes. The plants are particularly effective in industries that require rapid and uniform mixing (especially if the content of components is calculated in units or percentages) where it is necessary to treat suspensions (heterogeneous systems) regardless of theirRead More

Press

GlobeCore in the Press: Cemento Hormigón Magazine

The May-June 2018 number of Cemento Hormigón Magazine of Spain features an article by GlobeCore electrical engineer José Mora, titled “Re-trituración y mejora del cemento portland en los sistemas de optención de la capa vórtex de particulas ferromagnéticas”. The article describes GlobeCore experience in application of the vortex layer devices with ferromagnetic elements in theRead More

blank

The diesel fuel purification from sulphur

Another environmentally friendly solution by GlobeCore. This time we used an AVS-150 unit and a UVR unit for chemical desulfurization of diesel fuel. The outcome of the experiment is the reduction of sulfur concentration from 337 ppm to 8 ppm, bringing the sample into compliance with the Euro-5 standard.

blank

GlobeCore manufacturing

This video is a tour of GlobeCore manufacturing facility. You will see the stages of production of every unit, beginning with the order all the way to full production. This includes metal preparation and cutting, manufacturing of parts using CNC machines, sanding of surfaces, painting of complete equipment and, of course, factory acceptance tests ofRead More

Cement Crushing

Quartz grinding

Quartz is a natural mineral. It is quite common in the earth’s crust and has a number of important properties: high strength, resistance to fracture, and high sorption properties. Quartz is a component of rocks and minerals, and its mass fraction in the earth’s crust is more than 60%. In industry it is used mainlyRead More

cement activation

Cement Activation

Grinding precision is one of the main parameters of cement quality. This construction material is one of the few, whose strength is improved by interaction with molecules of water. It is important to ensure thorough hydration of the substance. Apparently, water binds smaller particles better. Specific surface is the parameter used in laboratory conditions toRead More

Press

GlobeCore in the press : “Industrial WaterWorld” magazine

The fifth issue for 2017 of “Industrial WaterWorld” magazine published an article entitled “Decontamination of Oily Wastewater Using Electromagnetic Vortex Layer Devices”. The article analyzed the main directions of cleaning and neutralization of wastewater containing oil, and the advantages and disadvantages of these methods. Also the article described  the principle of  operation of electromagnetic vortexRead More

Cement Crushing

Сement Crushing

Cement manufacturing is always one of the most actual and perspective industry. Cement is always important component for building. That’s why the new electromagnetic cement crushing machine is a valuable discovery of advanced technologies. It provides unique physical process. This machine can provide effective development of special concrete features. What for we need Сement CrushingRead More

Disintegrator machine from GlobeCore

Disintegrator Machine

A disintegrator is a type of crushing equipment used for fine grinding of materials. Such machines are widely used in the following industries: mining; chemical; building; food. Specifically, in the building industry this equipment crushes cement, sand, clay and other bulk materials, which are used for preparation of building mixtures. Depending on the grinding efficiency,Read More

Globecore

GlobeCore Opens a New Service Center in Costa-Rica

Dear friends! We are happy to announce that a new service center commenced operations in Costa-Rica in November 2017. This service center will assist our clients throughout the Latin America. A stock of spare parts will be made available to the clients. It is also possible to visit the new service center to purify andRead More

Press

GlobeCore in the press: an article published in “Water today” on wastewater treatment from heavy metals

The eighth issue of the scientific-research magazine “Water Today” of this year 2017 published an article “Electromagnetic Intensification of Heavy Metal Removal and Wastewater Decontamination”. This article deals with the problem of wastewater pollution from the chemical plant, petrochemical plant, engineering industry and food processing industry, and specifically addresses the purification of wastewater from chromium,Read More

blank

New service center in Houston is open

GlobeCore  announced the opening of a new service center in US. The address of the new location is 1750-H Dickinson Ave (FM 1266) Dickinson, TX, 77539. T: + 1-713-429-1616 and + 1-713-828-7877. Our other offices and service centers are available in the section “Contacts”. GlobeCore GmbH is one of the world leaders in industrial manufacturing.Read More

blank

GlobeCore has increased the production facility floor by 8,000 square meters

Our company has increased the production facility floor by 8,000 square meters at the end of 2013. GlobeCore GmbH is one of the world leaders in industrial manufacturing. Products of GlobeCore are used in transformer oil purification and degassing, insulation oil filtration, power transformer vacuuming. The head office is located in Oldenburg, Germany. Our systemsRead More