- 您需要先登录才可以创建新话题。
Jessica Mitchell
Jessica Mitchell
已创建论坛回复
-
作者帖子
-
? = Output (kW) / Input (kW). Load and no-load losses derived from SC/OC tests.
Total losses = No-load (core + dielectric) + Load losses (I²R + stray + eddy). Standards IEC/IEEE specify test-derived values using open-circuit/short-circuit tests and temperature correction. Losses are expressed in watts or kW at rated load for economic evaluation.
Ensures transient overvoltage control, enables single-line-to-ground fault detection, and reduces insulation stress.
Pole-mounted units reduce installation cost and provide LV service to neighborhoods. Elevation offers safety clearance and flood protection.
一月 25, 2026 3:35 下午 回复至： What is the importance of transformers in an electrical power system? #331877Transformers enable voltage adaptation for efficient transmission and safe distribution. They provide isolation, allow protection coordination, support reactive power flow, and permit integration of generation, transmission, and distribution segments into a unified grid.
Second-hand units are bought via refurbishers, utilities offloading old fleet, decommissioning contractors, and surplus marketplaces that provide test data.
S=VI for single-phase and S=?3VI for three-phase; ratings include thermal and impedance considerations.
一月 24, 2026 5:54 上午 回复至： How long does it take to replace a power transformer after failure? #331603Replacement depends on procurement lead time (months for large units), logistics, installation, oil processing, and commissioning; expedited replacements may still take weeks.
一月 23, 2026 2:12 上午 回复至： What certifications must a manufacturer of power transformers comply with for utility markets? #331373Manufacturers must comply with international and regional standards such as IEC 60076 or IEEE/ANSI C57 series for design, testing, insulation coordination, and performance. They may need ISO 9001 for quality management, ISO 14001 for environmental management, and ISO 45001 for occupational health and safety. For specific markets, utilities require type-test reports, routine-test certificates, and sometimes third-party certifications or grid code compliance. Seismic, fire, and EMC standards may also apply depending on installation conditions and regulatory frameworks.
It contains standardized test procedures, instrumentation requirements, acceptance criteria, and reporting templates for electrical, mechanical, and dielectric performance verification. Loss testing, impedance measurement, vector group checks, and oil diagnostics are usually included.
GSUs raise generator output to transmission voltages to reduce line losses; power transformers in substations later step voltage down for distribution.
一月 20, 2026 12:57 下午 回复至： How does a step down transformer alter voltage from a power line to a building? #330555Distribution transformers step line voltage (e.g., 11-33kV) down to service levels such as 230/400V or split-phase 120/240V for buildings.
一月 19, 2026 5:40 下午 回复至： What steps are involved in power transformer assembly during manufacturing? #330380Assembly involves core stacking, clamping, coil winding, insulation layering, core-coil assembly, brazing or soldering connections, lead routing, OLTC integration, bushing installation, tank assembly, vacuum oil filling, leak testing, and factory routine tests per IEC/IEEE.
ACTOM transformers are deployed across African utility networks, mining operations, industrial plants, and large commercial facilities. They serve MV/LV distribution, substation duty, and industrial feeders requiring robust mechanical short-circuit withstand.
The CMM-6/7 is a transformer oil purification plant with approximately 6-7 m³/h capacity. It removes water, gases, and impurities under vacuum. We will prepare a quotation and suggest equivalent models with the same performance and quality.
The TOR-80 LS is a semi-automatic breakdown-voltage tester rated up to 80 kV, compliant with IEC 60156. We will send a commercial offer with technical datasheet and lead time.
The TOR-1 is designed for measuring dissolved water in transformer and insulating oils. It is not calibrated for use with honey or food products. We can provide a quotation for the standard oil moisture measurement configuration.
十一月 7, 2025 8:50 上午 回复至： Please can you give me a quote on CMM-G Wind Turbine Gearbox Oil Changer #327094The CMM-G unit performs oil changing and filtration for wind turbine gearboxes. It includes heating, flow control, and filtration up to 3 microns. We will prepare a quotation and technical sheet.
The TOR-1 moisture meter measures water content in transformer oil in ppm. It provides results within 10 minutes per sample. We will send a quotation including lead time and specifications.
Key components include the core, windings, bushings, conservator, and oil system. Maintenance includes regular oil testing, filtration, thermal imaging, and tightening connections. GlobeCore provides full-cycle oil treatment systems that support preventive and predictive transformer maintenance.
-
作者帖子