CMM-6LT Industrial Oil Purification Unit
Cap: 6000 LPH | Degassing | Vacuum drying | 5 µm filtration
The mobile oil station CMM-6LT is designed for thermovacuum drying, filtration, and purification from mechanical impurities and water of oils used in lubrication systems, sealing systems, hydraulic control systems of gas turbine and gas compressor units, gas-motor-compressors, as well as transformers, during operation and maintenance.
The unit can be used for cleaning contaminated oils from water, free and dissolved gases, heating and drying oil-filled electrical apparatuses with hot transformer oil, using the thermovacuum drying method. Additionally, it can remove mechanical impurities through high-efficiency filter elements. The unit is applied in assembly, repair, and operational organizations engaged in oil processing and purification.
The unit can process mineral transformer oils with the following properties:
- kinematic viscosity at 50 °C – 2…12 mm2/s;
- oil mass moisture content – not more than 100 ppm;
- density at 20°C – 800…950 kg/m3;
- industrial cleanliness class according to ISO 4406 – not worse -/19/16.
|
No. |
Parameter |
Value |
| 1 | Capacity, m3/h (gal/min), at least
|
6 (26.4) 4-6 (17.6-26.4) |
| 2* | Processed oil parameters (after several passes):
— total gas content, %, max |
1.5 10 ppm, or 5 ppm, or 5 ppm+ (optional) -/14/12 |
| 3 | Max oil outlet temperature, ºC (ºF) |
55-60 (131-140) |
| 4 | Outlet pressure, bar (psi) |
3 (43.5) |
| 5 | Oil heater power, kW, max |
42 |
| 6 | Max power consumption, kW |
50 |
| 7 | Power supply parameters
voltage, V frequency, Hz number of phases |
380 50 3 |
| 8 | Overall dimensions, mm (in), max
— length |
1,100 (43.3) |
| 9 | Weight, kg (lbs), max |
475 (1,047) |
Note: *At initial oil parameters:
- volumetric gas content — below 10.5 %;
- mass moisture content — below 0.01 % (100 g/t);
- temperature — above 0 ºC (32 ºF).
Multiple passes of oil through the unit are required.
- Compactness
- Oil heating capability
- High degree of filtration
- High maneuverability
- Protection against oil overheating
- Oil drying
Application:
What is the difference between thermovacuum oil purification and oil regeneration?
Thermovacuum oil purification removes dissolved or suspended contaminants from the oil (water, gases, and mechanical impurities), while oil regeneration removes the aging products of the oil itself and restores its chemical properties to a condition close to that of new oil.
Can oil be processed using a CMM-6LT unit while the transformer is energized?
Yes. Oil processing in an energized transformer must not be prohibited by the regulations of the country where the transformer is installed. In addition, the CMM-6LT unit must be equipped with an automatic flow rate control system, and its connection to the transformer must be made using the TSS Transformer Safety System.
Can the acid number of oil be reduced by processing it with a CMM-6LT unit?
No. CMM-R oil regeneration units must be used for this purpose.
What type of vacuum system is used in the CMM-6LT unit?
A single-stage vacuum system. The system uses one vacuum pump to generate a low vacuum.
What vacuum level is generated by the vacuum system of the CMM-6LT unit?
Operating gauge pressure from −0.85 to −0.95 bar.
Webinars
Transformer Oil Processing Solutions by GlobeCore
Midel eN 1204 Natural Ester Dielectric Fluid Purification
Heat Transfer Oil Purification – Why Mineral HTF Systems Need It?
Nuclear Plant Hydraulic Oil Purification

