CMM-12R Oil Regeneration Systems
CMM-12R Oil Regeneration Systems
Cap: 1000-2000 LPH | Regeneration | Sorbent Reactivation | Economy
- Description
- Specifications
- Advantages
- Application
- Configurator
- Payback Period
- Video
- Gallery
- Publications
GlobeCore’s oil regeneration process restores used oils to a condition close to new oil. This process makes it possible to fill transformers with oil that would otherwise have been disposed of. The oil can be used in the transformer without replacement throughout its entire service life.
GlobeCore’s CMM-R systems are designed to extend the transformer’s lifespan by restoring the dielectric strength and chemical composition of dielectric insulating oil.
In the oil regeneration process, oil degradation products and acidic compounds are removed, the oil becomes clear, oxidation resistance improves, while its gas solubility is reduced.
| No. |
Parameter |
Value |
| 1 | Nominal capacity, L/h (gpm) |
1,000-2,000 (4.4-8.8) |
| 2 | Oil losses during operation, % |
2-25 |
| 3 | Maximum allowable oil temperature, °C (°F) |
90 (194) |
| 4 | Outlet pressure, bar (psi) |
2.5 (36.3) |
| 5 | Maximum power consumption, kW |
55 |
| 6 | Nominal vacuum suction rate, L/h (gpm) |
280,000 (1,232) |
| 7 | Fuller’s earth load, kg (lbs) |
1,600 (3,527) |
| 8 | Power supply parameters | |
| Voltage, V |
Customizable |
|
| Frequency, Hz | ||
| 9 | Coarse filtration degree (mesh filter), µm |
100 |
| 10 | Pre-filtration degree, µm |
25 |
| 11 | Fine filtration degree, µm |
5 |
| 12 | Dimensions, mm (in) | |
| Length |
5,500 (216.5) |
|
| Width |
2,320 (91.3) |
|
| Height |
2,450 (96.5) |
|
| 13 | Weight, kg (lbs) |
6,000 (13,227) |
Oil regeneration within a transformer restores waste oil to as good as new condition:
| Parameter | Before processing | After processing |
| Mass moisture content, g/t (ppm) as per IEC 733; ASTM D-1533 | 43 | 5 |
| Industrial purity grade as per ISO 4406 | -/18/16 | -/14/12 |
| Volumetric gas content, % as per IEC 60599; ASTM D-3612 | — | 0.1 |
| Acid number, mg KOH/g as per IEC 296; ASTM D-664 | 0.2 | 0.01 |
| Corrosive sulfur as per IEC 5662; ASTM D-1275 | present | not detected |
| Dielectric strength, kV as per IEC 156; ASTM D-18116 | 30 | 70 |
| Interfacial tension, N/m, at 25 °C as per IEC 6295; ASTM D-664 | — | 45 |
| Dissipation factor at 90 °C as per IEC 247; ASTM D-924 | 0.095 | 0.001 |
| Oxidation stability as per IEC 74; 164 hours | — | restored |
**GlobeCore** manufactures oil regeneration systems for both transformer manufacturers and transformer service providers.
**GlobeCore** units are loaded with a sorbent that captures all oil decomposition products.
**GlobeCore** regeneration systems can use the same sorbent for up to 3 years before the first replacement. No more need for consumables and costly labor related to the replacement of exhausted sorbent at the job site.
Regeneration systems can be combined with degassing units or purchased as stand-alone systems.
**GlobeCore** regeneration systems can be used in combination with your existing degassing or drying unit.
Each **GlobeCore** unit can be customized and includes a number of options:
- Extra vacuum pump assembly for transformer vacuuming;
- Mounted on a trailer or semi-trailer;
- Moisture meters at the inlet and/or outlet of the oil stream;
- Remote control and process monitoring via smartphone or PC;
- Climate-controlled operator workroom.
Application:
Webinars
GlobeCore’s Participation in IPSE TECH LATAM 2026
GlobeCore Tech School Hosts a Webinar on Compact LT Series Transformer Oil Processing Equipment
GlobeCore delivered three containerized transformer oil treatment complexes to Iraq
Reactivation clay polishing system for oils and fuels
